In multijet common rail (CR) systems, the capability to manage multiple injections with full flexibility in the choice of the dwell time (DT) between consecutive solenoid current pulses is one of the most relevant design targets. Pressure oscillations triggered by the nozzle closure after each injection event induce disturbances in the amount of fuel injected during subsequent injections. This causes a remarkable dispersion m the mass of fuel injected when DT is varied. The effects of the hydraulic circuit layout of CR systems were investigated with the objective to provide design rules for reducing the dependence of the injected fuel amount on DT. A multijet CR of the latest solenoid-type generation was experimentally analyzed at different operating conditions on a high performance test bench The considerable influence that the injector-supplying pipe dimensions can exert on the frequency and amplitude of the injection-induced pressure oscillations was widely investigated and a physical explanation of cause-effect relationships was found by energetics considerations, starting from experimental tests. A parametric study was performed to identify the best geometrical configurations of the injector-supplying pipe so as to minimize pressure oscillations. The analysis was carried out with the aid of a previously developed simple zero-dimensional model, allowing the evaluation of pressure-wave frequencies as functions of main system geometric data. Pipes of innovative aspect ratio and capable of halving the amplitude of injected-volume fluctuations versus DI were proposed. Purposely designed orifices were introduced into the rail-pipe connectors of a commercial automotive injection system, so as to damp pressure oscillations. Their effects on multiple-injection performance were experimentally determined as being sensible The resulting reduction in the injector fueling capacity was quantified. It increased by lowering the orifice diameter. The application of the orifice to the injector inlet-pipe with innovative aspect ratio led to a hydraulic circuit solution, which coupled active and passive damping of the pressure waves and minimized the disturbances in injected fue volumes. Finally, the influence of the rail capacity on pressure-wave dynamics was studied and the possibility of severely reducing the rail volume (up to one-fourth was assessed. This can lead to a system not only with reduced overall size but also with a prompter dynamic response during engine transients.

Hydraulic Circuit Design Rules to Remove the Dependence of the Injected Fuel Amount on Dwell Time in Multijet CR Systems / Baratta, Mirko; Catania, Andrea; Ferrari, Alessandro. - In: JOURNAL OF FLUIDS ENGINEERING. - ISSN 0098-2202. - STAMPA. - 130:12(2008), pp. 121104-1-121104-13. [10.1115/1.2969443]

Hydraulic Circuit Design Rules to Remove the Dependence of the Injected Fuel Amount on Dwell Time in Multijet CR Systems

BARATTA, MIRKO;CATANIA, ANDREA;FERRARI, Alessandro
2008

Abstract

In multijet common rail (CR) systems, the capability to manage multiple injections with full flexibility in the choice of the dwell time (DT) between consecutive solenoid current pulses is one of the most relevant design targets. Pressure oscillations triggered by the nozzle closure after each injection event induce disturbances in the amount of fuel injected during subsequent injections. This causes a remarkable dispersion m the mass of fuel injected when DT is varied. The effects of the hydraulic circuit layout of CR systems were investigated with the objective to provide design rules for reducing the dependence of the injected fuel amount on DT. A multijet CR of the latest solenoid-type generation was experimentally analyzed at different operating conditions on a high performance test bench The considerable influence that the injector-supplying pipe dimensions can exert on the frequency and amplitude of the injection-induced pressure oscillations was widely investigated and a physical explanation of cause-effect relationships was found by energetics considerations, starting from experimental tests. A parametric study was performed to identify the best geometrical configurations of the injector-supplying pipe so as to minimize pressure oscillations. The analysis was carried out with the aid of a previously developed simple zero-dimensional model, allowing the evaluation of pressure-wave frequencies as functions of main system geometric data. Pipes of innovative aspect ratio and capable of halving the amplitude of injected-volume fluctuations versus DI were proposed. Purposely designed orifices were introduced into the rail-pipe connectors of a commercial automotive injection system, so as to damp pressure oscillations. Their effects on multiple-injection performance were experimentally determined as being sensible The resulting reduction in the injector fueling capacity was quantified. It increased by lowering the orifice diameter. The application of the orifice to the injector inlet-pipe with innovative aspect ratio led to a hydraulic circuit solution, which coupled active and passive damping of the pressure waves and minimized the disturbances in injected fue volumes. Finally, the influence of the rail capacity on pressure-wave dynamics was studied and the possibility of severely reducing the rail volume (up to one-fourth was assessed. This can lead to a system not only with reduced overall size but also with a prompter dynamic response during engine transients.
File in questo prodotto:
Non ci sono file associati a questo prodotto.
Pubblicazioni consigliate

I documenti in IRIS sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.

Utilizza questo identificativo per citare o creare un link a questo documento: https://hdl.handle.net/11583/1895837
 Attenzione

Attenzione! I dati visualizzati non sono stati sottoposti a validazione da parte dell'ateneo